Hyperion EOS0610iDUOII Charger - User’s Manual
v1.2 Firmware version. Visit http://media.hyperion.hk/dn/eos for the newest manuals, firmware, and software
Warnings:
The EOS 0610i DUOII is a carefully-designed charger with many
built-in safety features, such as reverse polarity protection, input
voltage error warning, and cell-count mismatch warnings for lithium
chemistry batteries. HOWEVER, IT IS THE RESPONSIBILITY OF THE
USER TO INSURE THAT THE CHARGER IS CONFIGURED AND USED IN
A SAFE MANNER IN PROPER ENVIRONMENT.
• Always be sure that the charger is properly configured for
the correct battery type
• Be sure that your lithium battery pack balance connector
matches the multi-adapter type connected to the charger.
• SYNC MODE charging should start with packs at nearly equal
discharge states (see more details in text)
• Be sure that the batteries you charge are capable of
charging at the rate you select
• Never charge batteries unattended
• Charge only in a fire-resistant environment, non-flammable
surfaces such as on concrete or brick
• Do not charge near easily flammable materials
• Do not charge batteries inside a model
• Charging outdoors is recommended whenever practical
• Use only high-quality gold 4mm bullet connectors for charge
output cable connection to the charger. See “setup”
• Properly insulate and regularly inspect all connectors to
eliminate the possibility of short circuit. Damage caused by
output short circuit is not covered by warranty.
• Never allow the charger case to contact an AC/DC power
supply case while powered
• Do not drop or cause other shock to the charger, nor subject
it to moisture, condensation or liquids
• Do not attempt to charge battery packs made from different
types of cells, a mixture of old and new cells, or cells made
with chemistry not supported by the EOS 0610i DUOII
• NEVER attempt to charge “non-rechargeable” cells
• Do not open the case of the charger under any
circumstances. Doing so will void the warranty
• Keep the charger away from children or pets at all times.
• NEVER ATTEMPT TO CHARGE A SINGLE BATTERY
ACROSS BOTH PORTS.
(example: a “single unit” 10S pack) DOING
SO WILL DAMAGE THE CHARGER, BATTERY, AND WILL VOID
YOUR WARRANTY.
DUOII is designed to charge single packs up to 6S max.
For flight packs larger than 6S, DUOII supports SYNC MODE
charging of two packs to make a single series-wired flight
pack. (so 2x2S=4S up to 2x6S=12S series flight packs are
possible)
PUT SAFETY AHEAD OF ALL OTHER CONSIDERATIONS!
SEEK MEDICAL ATTENTION IN EVENT OF ANY INJURY!
Specifications & Features:
• 180W Per Port for 360 Watts Max CHARGE Output
• 0.1A to 10.0A max CHARGE Current in 0.1A steps
• 50W Per Port DISCHARGE with 10A Max Current
• STORE MODE allows fast and simple
charge/discharge to 60% capacity for proper
storage of Lithium Batteries = longer battery life.
• Charges/Discharges 1 to 6 cells Lithium Polymer
Batteries Per Port
(3.7V/cell nominal types)
• Charges/Discharges 1 to 6 cells Lithium Ion
Batteries Per Port
(3.6V/cell nominal types)
• Charges/Discharges 1 to 6 LiFePO4 (A123) cells
(LiFePO4 3.3V/cell nominal, A123 3.3v support)
• Charges/Discharges/Cycles 1-16 cell NiCd/Ni-MH in
three modes: Normal, Linear, and Automatic
• Charges/Discharges 1~12 cell Lead Acid Batteries
(Pb, 2V/cell)
• Allows Lithium-Type batteries to 50,000mAh and
PB (lead/acid) batteries to 100Ah capacity
• Two built -in Hyperion LBA10/300 Balancers with
10A max rating and 300mA max balance rate/cell
• TCS - Terminal Capacity Selection
• Rich Data Displays during and after charging and
balancing
• PC Port for Data Logging and Firmware upgrades
• Temperature Sensor Ports & Temp Stop settings*
• Wide Voltage Input Range 11v~28v for higher
efficiency when charging high-voltage packs, and
compatibility with a wider selection of AC/DC
power supplies
• Power Supply Amperage Control to allow reliable
charging with lower-output power supplies
• Power Supply Voltage Control (PS Load Control)
works in concert with Amperage control to insure
the charger does not overload your power supply
• Adjustable Power Sharing % between Outputs
• Input Cable with 4mm Male Connectors + Clamps
• Output Cable Set Included, with 4mm Connectors
• Two, Integral, Thermostat-Controlled Cooling Fans
• Rugged Aluminum Case with Insulating End Caps
• 2-Line, 16-Character, Yellow Backlit LCD Data
Display. Highly visible in all conditions
• Total of 20 User-definable Memory Positions
• Firmware upgradable via Win PC **
* Temp sensors available separate: #HP-EOSTMPSEN or EOS1210i-SEN
** Firmware upgrades require USB Adapter #HP-TI-PRGUSB and harness
#HP-EOS06-PCCBL. Firmware upgrades will only become available if and
when improvements are identified in future.
HIGH RISK CHARGING ADVISORY
Avoid charging batteries indoors. If you must charge indoors – or any
place injury to persons or damage to property could occur in the event
of fire – then be sure to:
* Keep battery well away from flammables (2 meters or more)
* Contain battery in a heavy fireproof container (such as a brick box)
* Always monitor the charge
HYPERION ACCEPTS NO RESPONSIBILITY FOR DAMAGE OR INJURY
FOR INDOOR or other HIGH RISK CHARGING ACTIVITY
1
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals